To-zone zone-name Release Information Command introduced in Junos OS Release 10.3. Command updated in Junos OS Release 10.4. Command updated in Junos OS Release 12.1. Command updated to include optional from-zone and to-zone global match options in Junos OS Release 12.1X47-D10. Description The show security match-policies command allows you to troubleshoot traffic problems using the match criteria: source port, destination port, source IP address, destination IP address, and protocol. For example, if your traffic is not passing because either an appropriate policy is not configured or the match criteria is incorrect, then the show security match-policies command allows you to work offline and identify where the problem actually exists. It uses the search engine to identify the problem and thus enables you to use the appropriate match policy for the traffic. The proper sequence of the commands to enable port security on F0/1 would be as follows: SW1(config)#interface fastethernet0/1. SW1(config-if)#switchport mode access. SW1(config-if)#switchport port-security. The above configuration applies a default security policy on the port. What settings are going to. Oct 17, 2017. This topic provides information about extended port Access Control Lists (ACLs) in Windows Server 2016. You can configure extended ACLs on the Hyper-V Virtual Switch to allow and block network traffic to and from the virtual machines (VMs) that are connected to the switch via virtual network adapters. The result-count option specifies how many policies to display. The first enabled policy in the list is the policy that is applied to all matching traffic. Other policies below it are “shadowed” by the first and are never encountered by matching traffic. Note: The show security match-policies command is applicable only to security policies; IDP policies are not supported. Options • destination-ip destination-ip—Destination IP address of the traffic. • destination-port destination-port–Destination port number of the traffic. Range is 1 through 65,535. • from-zone from-zone—Name or ID of the source zone of the traffic. • global—Display information about global policies. • protocol protocol-name| protocol-number–Protocol name or numeric value of the traffic. • ah or 51 • egp or 8 • esp or 50 • gre or 47 • icmp or 1 • igmp or 2 • igp or 9 • ipip or 94 • ipv6 or 41 • ospf or 89 • pgm or 113 • pim or 103 • rdp or 27 • rsvp or 46 • sctp or 132 • tcp or 6 • udp or 17 • vrrp or 112 • result-count number—(Optional) The number of policy matches to display. Valid range is from 1 through 16. The default value is 1. • source-end-user-profile device-identity-profile-name—(Optional) Device identity profile that specifies characteristics that can apply to one or more devices. • source-identity role-name—(Optional) Source identity of the traffic determined by the user role. • source-ip source-ip—Source IP address of the traffic. • source-port source-port—Source port number of the traffic. Range is 1 through 65,535. • to-zone to-zone—Name or ID of the destination zone of the traffic. Required Privilege Level view. Table 1: show security match-policies Output Fields Field Name Field Description Policy Name of the applicable policy. Action or Action-type The action to be taken for traffic that matches the policy’s match criteria. Actions include the following: • permit • firewall-authentication • tunnel ipsec-vpn vpn-name • pair-policy pair-policy-name • source-nat pool pool-name • pool-set pool-set-name • interface • destination-nat name • deny • reject State Status of the policy: • enabled: The policy can be used in the policy lookup process, which determines access rights for a packet and the action taken in regard to it. • disabled: The policy cannot be used in the policy lookup process, and therefore it is not available for access control. Index An internal number associated with the policy. Sequence number Number of the policy within a given context. For example, three policies that are applicable in a from-zoneA-to-zoneB context might be ordered with sequence numbers 1, 2, and 3. Also, in a from-zoneC-to-zoneD context, four policies might have sequence numbers 1, 2, 3, and 4. From zone Name of the source zone. To zone Name of the destination zone. Source addresses The names and corresponding IP addresses of the source addresses for a policy. Address sets are resolved to their individual address name-IP address pairs. Destination addresses The names and corresponding IP addresses of the destination addresses (or address sets) for a policy as entered in the destination zone’s address book. A packet’s destination address must match one of these addresses for the policy to apply to it. Application Name of a preconfigured or custom application, or any if no application is specified. IP protocol Numeric value for the IP protocol used by the application, such as 6 for TCP or 1 for ICMP. ALG If an ALG is associated with the session, the name of the ALG. Otherwise, 0. Inactivity timeout Elapsed time without activity after which the application is terminated. Source-port range Range of matching source ports defined in the policy. Destination-port range Range of matching destination ports defined in the policy. Source identities One or more user roles defined in the matching policy. Global Display information about global policies. Device-identity-profile-name Device identity profile that specifies characteristics that can apply to one or more devices. Sample Output.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
March 2018
Categories |